Jonsered CS 2135T Manual de usuario

CS 2135T Operator’ s manual (EP A II) Please read the oper ator’s manual carefully and make sure you understand the instructions before using the ma

10 – EnglishGENERAL SAFETY PRECAUTIONSMufflerThe muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.In

English – 11GENERAL SAFETY PRECAUTIONSBar• Length (inches/cm)• Number of teeth on bar tip sprocket (T). • Chain pitch (inches). The spacing between th

12 – EnglishGENERAL SAFETY PRECAUTIONSSharpening cutting teethTo sharpen cutting teeth you will need a round file and a file gauge. See instructions und

English – 13GENERAL SAFETY PRECAUTIONS• Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination

14 – EnglishGENERAL SAFETY PRECAUTIONSChain drive sprocketThe clutch drum is fitted with one of the following drive sprockets:A Spur sprocket (the ch

English – 15ASSEMBLYFitting the bar and chainCheck that the chain brake is in disengaged position by moving the front hand guard towards the front han

16 – EnglishFUEL HANDLINGFuelNote! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke

English – 17FUEL HANDLING• In temperatures below 32°F (0°C) some oils become too viscous. This can overload the oil pump and result in damage to the o

18 – EnglishSTARTING AND STOPPINGStarting and stoppingCold engineStarting: The chain brake should be activated when starting the chain saw. Activate t

English – 19STARTING AND STOPPING• Never start a chain saw unless the bar, chain and all covers are fitted correctly. See instructions under the headin

2 – English KEY T O SYMBOLS Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fat

20 – EnglishWORKING TECHNIQUESBefore use:1 Check that the chain brake works correctly and is not damaged.2 Check that the throttle lockout works corre

English – 21WORKING TECHNIQUESincorrectly or make the cut in the wrong place the tree may hit you or the machine and cause you to lose control. Both s

22 – EnglishWORKING TECHNIQUESCutting with the bottom edge of the bar, i.e. from the top of the object downwards, is known as cutting with a pulling c

English – 23WORKING TECHNIQUESThe log is supported at one end. There is a high risk that it will split.Start by cutting from below (about 1/3 of the w

24 – EnglishWORKING TECHNIQUESFellingFelling is done using three cuts. First you make the directional cuts, which consist of the top cut and the botto

English – 25WORKING TECHNIQUESLimbingMake sure that you can stand and move about safely. Work on the left side of the trunk. Work as close as possible

26 – EnglishMAINTENANCEGeneralThe user must only carry out the maintenance and service work described in this manual.Carburetor adjustmentDue to exist

English – 27MAINTENANCECorrectly adjusted carburetorWhen the carburetor is correctly adjusted the machine accelerates without hesitation and the machi

28 – EnglishMAINTENANCEChain catcherCheck that the chain catcher is not damaged and is firmly attached to the body of the chain saw.Vibration damping s

English – 29MAINTENANCE• Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by

English – 3 CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: ... 2Symbols in the operator’s man

30 – EnglishMAINTENANCEAn air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new

English – 31MAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

32 – EnglishTECHNICAL DATATechnical dataCS 2135TEngineCylinder displacement, cu.in/cm32,38/39Cylinder bore, inch/mm 1,57/40Stroke, inch/mm 1,22/31Idle

English – 33TECHNICAL DATARecommended original and replacement bar and chain combinationsFollowing is a list of recommended cutting equipment for the

34 – EnglishFEDERAL EMISSION CONTROL WARRANTY STATEMENT´®z+R@Q¶5x¨´®z+R@Q¶5x¨YOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protect

English – 35AMERICAN STANDARD SAFETY PRECAUTIONSSafety precautions for chain saw users(ANSI B 175.1-2000 Annex C)Kickback safety precautionsWith a bas

´®z+R@Q¶5x¨2006-11-19´®z+R@Q¶5x¨1150324-95

4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to buy a Jonsered product!Your purchase gives you access to professional h

English – 5 WHA T IS WHA T? What is what on the c hain saw? 1 Filter cover2 Front handle3 Front hand guard4 Starter5 Chain oil tank6 Starter handl

6 – English GENERAL SAFETY PRECA UTIONS Bef ore using a new chain saw • Please read this manual carefully.• Check that the cutting equipment is cor

English – 7 GENERAL SAFETY PRECA UTIONS chain sa w usage if possible. Your dealer, forestry school or your library can provide information about wh

8 – EnglishGENERAL SAFETY PRECAUTIONS• This movement activates a spring-loaded mechanism that tightens the brake band (C) around the engine drive syst

English – 9GENERAL SAFETY PRECAUTIONSWill my inetria activated chain brake always activate during kickback in the event of a kickback?No. First your b