Jonsered CS 2139T Manual del operador

CS 2139T Oper ator ′ s manual Please read the oper ator’s manual carefully and make sure you understand the instructions before using the machine.

10 – EnglishGENERAL SAFETY PRECAUTIONSMufflerThe muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.In

English – 11GENERAL SAFETY PRECAUTIONSSome terms that describe the bar and chainTo maintain the safety features of the cutting equipment, you should r

12 – EnglishGENERAL SAFETY PRECAUTIONSIt is very difficult to sharpen a chain correctly without the right equipment. We recommend that you use our file

English – 13GENERAL SAFETY PRECAUTIONSTension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.• Undo t

14 – EnglishGENERAL SAFETY PRECAUTIONS• Check that the groove in the edge of the bar is clean. Clean if necessary.• Check that the bar tip sprocket tu

English – 15ASSEMBLYFitting the bar and chainCheck that the chain brake is in disengaged position by moving the front hand guard towards the front han

16 – EnglishFUEL HANDLINGFuelNote! The machine is equipped with a two-stroke engine and must always be run using a mixture of petrol and two-stroke oi

English – 17FUEL HANDLINGFuellingClean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at

18 – EnglishSTARTING AND STOPPINGStarting and stoppingCold engineStarting: The chain brake must be engaged when the chain saw is started. Activate the

English – 19STARTING AND STOPPING• Never start a chain saw unless the bar, chain and all covers are fitted correctly. See instructions under the headin

2 – English KEY T O SYMBOLS Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fat

20 – EnglishWORKING TECHNIQUESBefore use:1 Check that the chain brake works correctly and is not damaged.2 Check that the throttle lockout works corre

English – 21WORKING TECHNIQUES7 Take great care when cutting a tree that is in tension. A tree that is in tension may spring back to its normal positi

22 – EnglishWORKING TECHNIQUES8 Take great care when you cut with the top edge of the bar, i.e. when cutting from the underside of the object. This is

English – 23WORKING TECHNIQUESCuttingThe log is lying on the ground. There is little risk of the chain jamming or the object splitting. However there

24 – EnglishWORKING TECHNIQUESOnce you have decided which way you want the top of the tree to fall you must assess which way the top of the tree would

English – 25WORKING TECHNIQUESFinish the felling cut parallel with the directional cut line so that the distance between them is at least 1/10 of the

26 – EnglishWORKING TECHNIQUESHow to avoid kickbackWhat is kickback?The word kickback is used to describe the sudden reaction that causes the chain sa

English – 27MAINTENANCEGeneralThe user must only carry out the maintenance and service work described in this manual.Carburettor adjustmentDue to exis

28 – EnglishMAINTENANCECorrectly adjusted carburettorWhen the carburettor is correctly adjusted the machine accelerates without hesitation and 4-cycle

English – 29MAINTENANCE• Start the chain saw and apply full throttle. Release the throttle control and check that the chain stops and remains stationa

English – 3 CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: ... 2Symbols in the operator’s ma

30 – EnglishMAINTENANCEStarterChanging a broken or worn starter cord• Loosen the screws that hold the starter against the crankcase and remove the sta

English – 31MAINTENANCEAir filterThe air filter must be regularly cleaned to remove dust and dirt in order to avoid:• Carburettor malfunctions• Starting

32 – EnglishMAINTENANCEAdjustment of the oil pumpThe oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combinat

English – 33MAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

34 – EnglishTECHNICAL DATA´®z+Rvh¶6|¨´®z+Rvh¶6|¨Technical dataNote 1: Noise emissions in the environment measured as sound power (LWA) in conformity w

English – 35TECHNICAL DATABar and chain combinationsThe following recommended combinations of bar and saw chain are type approved for your chain saw.

´®z+Rvh¶6|¨2007-05-11´®z+Rvh¶6|¨1150867-26

4 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to buy a Jonsered product!We are convinced that you will appreciate with

English – 5 WHA T IS WHA T? What is what on the c hain saw? 1 Filter cover2 Front handle3 Front hand guard4 Starter5 Chain oil tank6 Starter handl

6 – English GENERAL SAFETY PRECA UTIONS Bef ore using a new chain saw • Please read this manual carefully.• Check that the cutting equipment is cor

English – 7 GENERAL SAFETY PRECA UTIONS chain sa w usage if possible. Your dealer, forestry school or your library can provide information about wh

8 – English GENERAL SAFETY PRECA UTIONS • This movement activates a spring-loaded mechanism that tightens the brake band (C) around the engine driv

English – 9 GENERAL SAFETY PRECA UTIONSWill my inetria activated chain brake always activate during kickback in the event of a kickback?No. First y