Jonsered GC 2125C Manual de usuario

GT 2125 GC 2125 GC 2125C Oper ator’s manual (EPA) Please read the oper ator’s manual carefully and make sure you understand the instructions before

10 – EnglishGENERAL SAFETY PRECAUTIONSGeneral rulesOnly use cutting attachments with the guards we recommend! See the chapter on Technical data.Keep t

English – 11ASSEMBLYFitting the loop handle(GT 2125)• Position the handle on the shaft. Note that the handle must be mounted below the arrow on the sh

12 – EnglishASSEMBLYAssembling and dismantling the two-piece shaft(GC 2125C)Assembly:• Loosen the coupling by turning the knob.• Align the tab of the

English – 13ASSEMBLY• Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger and

14 – EnglishASSEMBLYFitting the trimmer guard and trimmer head(GT 2125)Guard• Fit the guard as shown in the diagram. Tighten securely.Trimmer head• Fi

English – 15FUEL HANDLINGFuel safetyNever start the machine:1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evapor

16 – EnglishFUEL HANDLINGMixing• Always mix the gasoline and oil in a clean container intended for fuel.• Always start by filling half the amount of th

English – 17STARTING AND STOPPINGCheck before starting• Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the cent

18 – EnglishSTARTING AND STOPPINGCAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully

English – 19WORKING TECHNIQUESGeneral working instructionsBasic safety rules1 Look around you:• To ensure that people, animals or other things cannot

2 – English KEY T O SYMBOLS Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in s

20 – EnglishWORKING TECHNIQUESGrass clearing using a grass blade• Grass blades and grass cutters must not be used on woody stems.• A grass blade is us

English – 21WORKING TECHNIQUESSweeping• The fan effect of the rotating cord can be used for quick and easy clearing up. Hold the cord parallel to and

22 – EnglishMAINTENANCECarburetorYour Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engi

English – 23MAINTENANCEFine adjustment of the idle speed TAdjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. Fir

24 – EnglishMAINTENANCECooling systemTo keep the working temperature as low as possible the machine is equipped with a cooling system.The cooling syst

English – 25MAINTENANCETwo-piece shaft (GC 2125C)The drive shaft end in the lower shaft should be lubricated with grease every 30 hours. There is a ri

26 – EnglishMAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

English – 27TECHNICAL DATATechnical dataNote 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure lev

28 – EnglishTECHNICAL DATAThe accessories are recommended for use in combination with the specified power heads and have been evaluated to applicable I

English – 29FEDERAL EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protection Agency), Environme

English – 3 CONTENTS Contents Note the f ollowing before starting: Please read the oper ator’s manual carefully.Maintenance, replacement, or repair

"Clic"12356796,0 m18'483,05 m9'2,0-2,4 mm.079-.095"10 cm 4"6"15 cmTap-N-Go 25

1Trimmy H II234567897,5 m 25'2,0-2,4 mm.080-.095"12 15 cm 6"~ 3,7 m 12' 15 cm 6"

"Clic"12356710118,5 m28'484,2 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cmS35

12432,4-2,7 mm.095-.106"4,25 m14'4,25 m14'B6"15 cmA6"15 cmS355

´®z+R;3¶5y¨´®z+R;3¶5y¨Tap-N-Go 35"Clic"12356798,5 m28'484,3 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cm

1Auto 3223456789104,0 m 13'2,4 mm.095"~2,0 m6,5'6"6"15 cm15 cm

´®z+R;3¶5y¨2007-01-25´®z+R;3¶5y¨1150271-95

4 – English INTR ODUCTION Dear customer! Cong ratulations on your choice to buy a Jonsered product!Your purchase gives you access to professional h

English – 5 WHA T IS WHA T? What is what?3130GC2125C 1 Trimmer head2 Grease filler cap, bevel gear3 Bevel gear4 Cutting attachment guard5 Shaft6 Lo

6 – English GENERAL SAFETY PRECA UTIONS Impor tant Personal protective equipment HELMET A protectiv e helmet where there is a risk of falling objec

English – 7 GENERAL SAFETY PRECA UTIONS CLO THINGWear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches

8 – English GENERAL SAFETY PRECA UTIONS Cutting attac hment guard This guard is intended to pre vent loose objects from being thrown towards the op

English – 9GENERAL SAFETY PRECAUTIONSIf the muffler on your machine is fitted with a spark arrestor screen this must be cleaned regularly. A blocked scr